ASTM A564 PDF

Best Stainless offers high quality standards including UNS S, AMS , ASTM A, and ASTM A Grade PH stainless steel can be used. This standard is issued under the fixed designation A /A M; the number . [ mm] round bar, 10 to 12 ft [ to m] in length, ASTM A See the chemical composition and physical properties of ASTM A Grade condition HM, find alternative materials, and connect with suppliers.

Author: Kigashicage Virisar
Country: Libya
Language: English (Spanish)
Genre: Business
Published (Last): 1 November 2017
Pages: 380
PDF File Size: 6.45 Mb
ePub File Size: 12.1 Mb
ISBN: 720-6-30394-414-9
Downloads: 8505
Price: Free* [*Free Regsitration Required]
Uploader: Zulkit

Type XM is machinable in the as-received fully heat treated condition. Materials and Manufacture 5. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn. Applications should be limited aatm small diameter bar. F Columbium plus tantalum 0. Originally approved in Billets or bars for reforging may be purchased to this specification.

Type UNS S shall be furnished in solution annealed, cold-worked or aged-hardened condition. They are suitable for machining in the solution-annealed condition after which they may be age-hardened to the mechanical properties specified in Section 7 without danger of cracking asttm distortion. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part xstm the standard.

  ATREVETE A DISCIPLINAR DOBSON PDF

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Up to 6 in.

G Either Rockwell C hardness or Brinell is permissible. Combining values from the two systems may result in nonconformance with the specication. The specimens shall be heat treated in accordance with 5.

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are z564, complete or up to date. Such requirements may include but are not limited to the following: Warm in air to room temperature. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM A – Martensitic Stainless Steel

The values stated in each system are not exact equivalents; therefore, each system must be used independent of the other.

Hold ast not less than 3 h. Work Item s – proposed revisions of this standard. H When air cooling is specied, gases other than air may be used. For billets and bars for forging see Specification A The tests shall meet the requirements of Table 4.

CW 12 hard CW full hard 7.

ASTM A A M R_百度文库

Billets or bars for reforging may be purchased to this specification. Applications should be limited to small diameter bar.

Applications should be limited to small diameter bar. Link to Active This link will always route to the current Active version of the standard. Applications should be limited to small diameter bar. The material shall be subjected to tension, impact, and hardness tests.

  ALLEN CARR NICHTRAUCHER PDF

ASTM A564 Grade 630 condition H1150M

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. C Unless otherwise noted, temperatures shown are suggested temperatures and may be varied to obtain required tensile properties. I Refer to Table 2 for details on equalize and over temper adtm treatment.

Current edition approved May 1, C Either Rockwell C hardness or Brinell is permissible. Number of Tests 8.

T – Transverse axis of specimen perpendicular to direction of grain ow during rolling or forging. Combining values from the two systems may result in nonconformance with the specification. E L – Longitudinal axis of specimen parallel to direction of grain ow during rolling or forging.

Hot-finished or cold-finished rounds, squares, hexagons, bar shapes, angles, tees, and channels are included; these shapes may be produced by hot rolling, extruding, or forging. D BH for rounds cold drawn after solution treating.

Historical Version s – view previous versions of standard.