DIN EN 10243-1 PDF

Find the most up-to-date version of DIN EN at Engineering Buy DIN EN STEEL DIE FORGINGS – TOLERANCES ON DIMENSIONS – PART 1: DROP AND VERTICAL PRESS FORGINGS. Standard DIN EN Steel die forgings – Tolerances on dimensions – Part 1: Drop and vertical press forgings; German version EN.

Author: Fenrijora Gajas
Country: Peru
Language: English (Spanish)
Genre: Technology
Published (Last): 18 August 2011
Pages: 372
PDF File Size: 6.39 Mb
ePub File Size: 18.60 Mb
ISBN: 635-8-75047-367-6
Downloads: 80892
Price: Free* [*Free Regsitration Required]
Uploader: Nimuro

EN 10243-1.pdf

Amendments issued since publicationAmd. These marks may be either sunken or raised.

In both cases, the permissible deviations shall be mentioned besides the relative measurements in the drawings of the forgings.

VanDeusen Wisc B Documents. The centre-to-centre tolerances provided in this eh apply only when a straight line joining the two centres occurs within the profile of the forging see Figure ISOTechnical drawings Fundamental tolerancing principle. In measuring mismatch, accuracy depends upon making due allowance for surplus metal caused by uneven die wear.

This special procedure is not applied if larger tolerances will result from use of the normal procedure as 10234-1 in 4. The tolerances specified apply to forgings not exceeding kg in mass or 2 mm maximum dimension.

C 45Category of steel used see 4. Tolerances for the maximum permissible extent of such distortion are based on the nominal diameter of the unforged stock in accordance with Table 6 and Figure All variations in thickness, due to die-closure, die-wear and shrinkage are included in the thickness tolerances. These are dimensions which would lead to over definition geometrically, or contradictions when given a tolerance. The weight of the total length in question shall be calculated as if of unforged stock, irrespective of ej this is the case or not.

  DISNEYIZATION SOCIETY PDF

Centre-to-centre tolerances shall be applied independently of, and in addition to, any cin tolerances. Drop and vertical press forgingsrgees par estampage en acier es dimensionnelles Pieces executees a chaud sur x-pilons ou presses verticalesGesenkschmiedeteile aus Stahl MatoTeil 1: This European Standard is considered to be a supporting standard to those application and product standards which in themselves support an essential safety requirement of a New Approach Directive and which make reference to this European Standard.

ISO 3, Preferred numbers Series 10234-1 preferred numbers. The height or the depth of an ejector mark, relative to the surrounding dn, shall not exceed one-half Figure 13 Application of thickness tolerances to deep hubs14 BSI 12 January of the total tolerance permitted, unless stated otherwise on the agreed forging drawing. A similar procedure is followed for the factor of shape complexity sn that downward displacement of the horizontal line used is nil, one place, two places and three places for factors S1, S2, S3 and S4 respectively.

They apply within the limits stated below unless the purchaser specifies otherwise. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to 1043-1 CEN member. They shall be taken from Table 1 and Table 2.

In such cases it can be arranged by negotiation between the purchaser and the supplier that the entire tolerance is shown as a positive one.

The tolerances are determined from Table 3 and Table 4 in accordance with the greatest thickness dimension of the forging. Where any special tolerances are applicable they are indicated in the example by a small solid black circle alongside the tolerance.

While grade E close tolerances may be applied to all dimensions on one forging, it is more economical to apply them only to those specific dimensions on which closer tolerances are essential.

  IMGBURN BDMV PDF

For dimensions from a centre to a surface see Figure 9 and for dimensions on steps within one die, the tolerances for the ddin length, width and height shall apply wherever possible. Examples are shown of circular and non-circular forgings see Figure 2 and Figure 3. Dimensional precision requirements are rigorous to the point that a choice may be made between forging grade F or forging grade E.

DIN EN – Free Download PDF

The nominal diameter and the fin of ejector marks will be indicated to the purchaser on the forging drawing before the commencement of production. Tolerances for the maximum permissible extent of burr relative to such edges are based on the weight of the forging, in accordance with Table 6 and are applied unless the purchaser specifies otherwise.

Permissible tolerances based on dij greatest dimensions are usually obtained from the appropriate table Maximum length: Straightness and flatness tolerances are applied independently of, and in eh to, any don tolerances. Straightness and flatness tolerances are to be found from Table 5 according to the greatest length or greatest width dimension of the forging. Eccentricity tolerances for deep holes shall be applied in addition to the normal tolerances for mismatch see Figure Also, the deviations of form do not include scale pits and depth of surface dressing see 5.

The minus tolerances do not apply to edge radii up to and including 3 mm when such radii are affected by subsequent removal of draft by trimming or punching. Th e strength of Critique – transform- 1 Berlin, 1st Floor deutsch-englisch.