LA3600 DATASHEET PDF

LA datasheet, LA circuit, LA data sheet: SANYO – 5-Band Graphic Equalizer,alldatasheet, datasheet, Datasheet search site for Electronic. LA datasheet LA component LA integrated circuit LA schematic LA application note A LA LA36 LA3. Sanyo LA datasheet, 5-Band Graphic Equalizer (1-page), LA datasheet, LA pdf, LA datasheet pdf, LA pinouts.

Author: Goltizil Gular
Country: Romania
Language: English (Spanish)
Genre: Love
Published (Last): 9 July 2011
Pages: 189
PDF File Size: 1.4 Mb
ePub File Size: 14.26 Mb
ISBN: 539-3-90696-575-5
Downloads: 53862
Price: Free* [*Free Regsitration Required]
Uploader: Tojara

Capacitor C13 is a decoupling capacitor and C14 is a power supply filter circuit. Assemble the circuit on a good quality PCB. You may also like: This will la6300 good only when following are carried out.

Assemble the circuit on a good quality PCB. How we connect stereo input to this circuit? Leave a Reply Cancel reply Your email address will not be published. If you use slider potentiometers as controls and mount them vertically in a sequence datasheey left to right as R1 to R5 and as you slide it down, should cut the frequency spectrum for which it is meant and sliding up should boost.

C12 is the output capacitor and resistor R6 limits the supply current. Could i add this to my homemade tube amp, and take out the LA? Gain of each band can be adjusted by using the corresponding potentiometers R1 to R5. C12 is the output capacitor and resistor R6 limits the datashet current. Most of the IC manufacturers call their multi band tone controls as graphic equalisers.

  CHOPIN NOKTURNY PDF

Leave a Reply Cancel reply Your email address will not be published.

Capacitors C2, C4, C6, C8, C10 and C15 are the input capacitors and increasing the value of these capacitors will increase the low frequency response. Then the contour of the knobs represents the frequency response of the tone control unit.

Previous post Next post. LA is a single integrated single Op-amp, 5 band graphic equalizer IC which is very suitable for applications like portable stereo, radio sets, home theater systems, car audio systems etc.

LA Sanyo 5-band Graphic Equalizer ChipFind Datasheet Archive |

I used 9V DC for powering the circuit. If you use slider potentiometers as controls and mount lw3600 vertically in a sequence from left to right as R1 to R5 and as you slide it down, should cut the frequency spectrum for which it is meant and sliding l3600 should boost. The power supply must be well regulated and noise free.

The LA can be operated from anything between 5 to 15V DC and is extremely stable to capacitive loads. Most of the IC manufacturers call their multi band tone controls as graphic equalisers.

LA3600 datasheet download

Then the contour of the knobs represents the frequency response of the tone control unit. Capacitor C13 is a decoupling capacitor and C14 is a power supply filter circuit. Your email address will not be published. I used 9V DC for powering the circuit.

  APPENDICITE AIGUE COMPLICATION PDF

Capacitors C2, C4, C6, C8, C10 and C15 are the input capacitors and increasing the value of these capacitors will increase the low frequency response. LA is a single integrated single Op-amp, 5 band graphic equalizer IC which is very suitable for applications like portable stereo, radio sets, home theater systems, car audio systems etc.

Could i add this to my homemade tube amp, and take out the LA? The LA can be operated from anything between 5 to 15V DC and is extremely stable to capacitive loads.

(PDF) LA3600 Datasheet download

How we connect stereo input to this circuit? This will hold good only when following are carried out. Previous post Next post. The power supply must be well regulated and noise free.

In the circuit capacitors C1, C3, C5, C7 and C9 are used to fix the resonance frequency of the datasgeet bands. Hi Eric Nice question.

In the circuit capacitors C1, C3, C5, C7 and C9 are used to fix the resonance frequency of the corresponding bands. Hi Eric Nice question. You may also like: Your email address will not be published. Gain of each band can be adjusted by using the corresponding potentiometers R1 to R5.